Bereik in één oogopslag
- Capaciteitsbereik – 30 ml tot 1,500 ml, plus 1 gallon bulkemmers
- Bestaande mallen – 37 Mallen voor PET-flessen
- Materiaal en kleur – Duidelijk, amberkleurig en gekleurd transparant PET
- Sluitingen beschikbaar – Schroefdop, sport pet, trigger-sproeier, pomp
- Typische inhoud – Flessenwater en mineraalwater, sap en frisdranken, eetbare olie en azijn, monster- en reisformaatcosmetica, huishoudelijke schoonmaakmiddelen
Waarom voor flessen PET wordt gekozen
HUISDIER (polyethyleentereftalaat) is a polyester with an intrinsic viscosity that determines how much the resin can be stretched during blow moulding. The properties that matter for packaging decisions are:
- Helderheid – PET is naturally transparent and glossy, so bottle contents are fully visible and shelf appeal is high without extra decoration.
- Strength-to-weight ratio – PET containers are light for their strength, which lowers freight cost and packaging weight.
- Gas and moisture barrier – PET holds carbonation and protects against oxygen ingress, which is why it dominates carbonated soft drinks and bottled water.
- Recycleerbaarheid – PET carries resin identification code 1 and has the most developed recycling stream of any packaging plastic. Food-grade recycled PET (rPET) can be used in new beverage bottles where local regulations allow.
- Temperature limit – standard PET softens at roughly 70 °C, so it is not suitable for hot filling without heat-set tooling. For hot-fill or pasteurised products, PP or heat-set PET is the correct route.
Beverage applications normally also require the resin to meet food-contact requirements such as FDA 21 CFR 177.1630 en ik 10/2011, and for carbonated or oxygen-sensitive products the barrier grade and bottle design need to be agreed before tooling.
PET bottle moulds in our range
These items span the capacity bands and applications most often requested by beverage, water, cosmetic and household brands:
- 80ml PET-klein flesje voor monster en reizen
- 100ml PET-doorzichtige fles voor etherische olie
- 250ml PET-doorzichtige fles voor drank
- 500ml PET-trigger-spuitfles voor reiniging
- 1500ml PET-fles - 1.5L Grote drankverpakkingen
- Doorzichtige PET-emmer 1 Gallon - Bulkvloeistofverpakking
- 200ml PET-transparante fles voor drinkwater
- 300ml PET-ronde fles voor drinkwater
- 500ml PET-doorzichtige fles voor mineraalwater
- BPA-vrije plastic waterfles - Herbruikbaar & Veilig
- 100ml PET-doorzichtige sapfles voor drankverpakkingen
- 300ml PET-slanke fles voor drank
Each product page gives the neck finish and the closures that fit that mould. If your required size sits between two listed items, the same tooling family can often be run at an intermediate capacity.
How to specify a PET bottle
- Producttype – stilstaand water, carbonated drinks, sap, edible oil and household liquids each demand a different balance of barrier, pressure resistance and fill temperature.
- Carbonation – carbonated products need a pressure-rated design with a reinforced base; still products do not, and using a carbonation-rated bottle where it is not needed adds cost and weight.
- Fill temperature – standard PET handles cold and ambient fill. Hot fill, pasteurisation or retort require heat-set tooling or a different polymer.
- Hals afwerking – determines cap type: standard screw, PCO for carbonated drinks, sport pet, sprayer or pump. This is the constraint that everything else follows.
- Colour and clarity – duidelijk, amber, gekleurd transparant of ondoorzichtig. Light-sensitive products need amber or an opaque option.
- Duurzaamheid – specify whether recycled content is required and at what percentage, since that affects the grade selection and the documentation you will need.
Toepassingen die wij leveren
Current PET moulds serve bottled water and mineral water, sap en frisdranken, eetbare olie en azijn, monster- en reisformaatcosmetica, and household cleaning products. Typical items in the range include 100 ml clear juice bottles, 250 ml and 300 ml drinking-water bottles, 500 ml mineral-water and trigger-spray bottles, and 1.5 litre large beverage packaging.
Wat we controleren vóór verzending
Release checks on PET bottles normally cover dimensional accuracy, fill capacity by weight of water, wanddikteverdeling, neck finish and thread dimensions, dopkoppel en afdichtingsintegriteit, helderheid en kleur ten opzichte van het goedgekeurde monster, and print registration. Carbonated and hot-fill designs carry additional pressure or heat tests as agreed with the buyer.
Veelgestelde vragen
What is the difference between PET bottle suppliers and PET bottle manufacturers?
A supplier sells bottles that are typically made by a third party; a manufacturer owns the moulds, blow-moulding lines and quality process. Buying directly from a manufacturer gives you control over the tool, the wall specification, the resin grade and the inspection plan, which matters when packaging has to pass a food-contact audit.
Can PET bottles be used for hot drinks?
Standard PET is not suitable for hot fill because it softens around 70 °C. Hot-fill and pasteurised products require heat-set PET tooling or a switch to PP, which tolerates much higher fill temperatures.
Do you supply bottles made from recycled PET?
rPET is available where the application and your market's rules allow. Recycled content affects grade selection, colour and the documentation set, so it is best specified at the start of the project rather than after tooling.
What bottle weight should I choose?
Weight is a trade-off between shelf presence, top-load strength, barrier performance and cost. Lightweighting is normal for still water; carbonated and large-format bottles need more material to hold internal pressure and stacking loads.
Can you match a specific neck finish used by my existing cap supplier?
Ja, provided the neck geometry is a standard or can be replicated. Send the cap drawing or a physical sample and the corresponding neck specification can be confirmed before tooling.
How do I get a quotation for a PET bottle?
Stuur de capaciteit, producttype, whether the product is carbonated, vul temperatuur, neck finish or cap type, doelhoeveelheid, kleur- en artworkvereisten. With those we can match an existing mould or quote a new one.
WeChat-ID